XgDm9161aRegs

Defines
#define	NIC_PHY_BMCR   0x00
	Basic mode control register.
#define	NIC_PHY_BMCR_COLTEST   0x0080
	Collision test.
#define	NIC_PHY_BMCR_FDUPLEX   0x0100
	Full duplex mode.
#define	NIC_PHY_BMCR_ANEGSTART   0x0200
	Restart auto negotiation.
#define	NIC_PHY_BMCR_ISOLATE   0x0400
	Isolate from MII.
#define	NIC_PHY_BMCR_PWRDN   0x0800
	Power-down.
#define	NIC_PHY_BMCR_ANEGENA   0x1000
	Enable auto negotiation.
#define	NIC_PHY_BMCR_100MBPS   0x2000
	Select 100 Mbps.
#define	NIC_PHY_BMCR_LOOPBACK   0x4000
	Enable loopback mode.
#define	NIC_PHY_BMCR_RESET   0x8000
	Software reset.
#define	NIC_PHY_BMSR   0x01
	Basic mode status register.
#define	NIC_PHY_BMSR_ANCOMPL   0x0020
	Auto negotiation complete.
#define	NIC_PHY_BMSR_LINKSTAT   0x0004
	Link status.
#define	NIC_PHY_ID1   0x02
	PHY identifier register 1.
#define	NIC_PHY_ID2   0x03
	PHY identifier register 2.
#define	NIC_PHY_ANAR   0x04
	Auto negotiation advertisement register.
#define	NIC_PHY_ANLPAR   0x05
	Auto negotiation link partner availability register.
#define	NIC_PHY_ANEG_NP   0x8000
	Next page available.
#define	NIC_PHY_ANEG_ACK   0x4000
	Ability data reception acknowledged.
#define	NIC_PHY_ANEG_RF   0x2000
	Remote fault.
#define	NIC_PHY_ANEG_FCS   0x0400
	Flow control supported.
#define	NIC_PHY_ANEG_T4   0x0200
	100BASE-T4 supported
#define	NIC_PHY_ANEG_TX_FDX   0x0100
	100BASE-T full duplex supported
#define	NIC_PHY_ANEG_TX_HDX   0x0080
	100BASE-T half duplex supported
#define	NIC_PHY_ANEG_10_FDX   0x0040
	10BASE-T full duplex supported
#define	NIC_PHY_ANEG_10_HDX   0x0020
	10BASE-T half duplex supported
#define	NIC_PHY_ANEG_BINSEL   0x001F
	Binary encoded protocol selector.
#define	NIC_PHY_ANER   0x06
	Auto negotiation expansion register.
#define	NIC_PHY_BMCR   0x00
	Basic mode control register.
#define	NIC_PHY_BMCR_COLTEST   0x0080
	Collision test.
#define	NIC_PHY_BMCR_FDUPLEX   0x0100
	Full duplex mode.
#define	NIC_PHY_BMCR_ANEGSTART   0x0200
	Restart auto negotiation.
#define	NIC_PHY_BMCR_ISOLATE   0x0400
	Isolate from MII.
#define	NIC_PHY_BMCR_PWRDN   0x0800
	Power-down.
#define	NIC_PHY_BMCR_ANEGENA   0x1000
	Enable auto negotiation.
#define	NIC_PHY_BMCR_100MBPS   0x2000
	Select 100 Mbps.
#define	NIC_PHY_BMCR_LOOPBACK   0x4000
	Enable loopback mode.
#define	NIC_PHY_BMCR_RESET   0x8000
	Software reset.
#define	NIC_PHY_BMSR   0x01
	Basic mode status register.
#define	NIC_PHY_BMSR_ANCOMPL   0x0020
	Auto negotiation complete.
#define	NIC_PHY_BMSR_LINKSTAT   0x0004
	Link status.
#define	NIC_PHY_ID1   0x02
	PHY identifier register 1.
#define	NIC_PHY_ID2   0x03
	PHY identifier register 2.
#define	NIC_PHY_ANAR   0x04
	Auto negotiation advertisement register.
#define	NIC_PHY_ANLPAR   0x05
	Auto negotiation link partner availability register.
#define	NIC_PHY_ANER   0x06
	Auto negotiation expansion register.

---